3.7V 1500mAh Lithium Polymer Battery for Warm Clothes

- Nov 17, 2016 -

3.7V 1500mAh Lithium Polymer Battery for Warm Clothes Basic Info
  • Model NO.: 603759 3.7V 1500mAh

  • Charger Type: Electric Charger

  • Nominal Voltage: 3.7V

  • Compatible Battery Type: 3.7V

  • Certification: RoHS, CE

  • Lipolymer Battery: 603759

  • Package: Boxes

  • Origin: China

  • Type: Li-Polymer Battery

  • Charger Application: Standard Battery

  • Charger Style: Cc-CV

  • Size: 5.8*37*59

  • Recyclable: Recyclable

  • Specification: 603759 3.7V 1500mAh

  • HS Code: 8507600090

Product Description

Advantage:
1.Small size,but high density,high capacity.0.5C discharger over 1500mAh.
2.Performance is stable,99% cells can be matched.

3.All the cells accepted 85 ºC baking.

3.7V 1500mAh Lithium Polymer Battery

Specification:
603759 3.7V 1500mAh
Dimension:5.8*37*59mm
Weight Approx:31.4g
Voltage:3.7V
Capacity:1500mAh
Overcharge detection voltage:4.25V/cell,+/-25mV
Overdischarge detection voltage:3.0V

3.7V 1500mAh Lithium Polymer Battery

Application:
Digital products,intellectual products,warming clothes,GPS.




Electrical characteristics:

1.Standard Charge:
Charging the cell initially with constant current at 0.5C and then with constant voltage at 4.2V till charge current declines to 0.05C.

2.Cycle Life:
80% or more of 1 st cycle capacity at 0.5C discharge of Operation.

3.Self-discharge:
After the standard charging, storied the cells under the condition as No.6.4 for 28 days, then measured the capacity with 0.5C till 3.0V,Residual capacity>90%.


Mechanical characteristics:

1.Vibration Test:
After standard charging, fixed the cell to vibration table and subjected to vibration cycling that the frequency is to be varied at the rate of 1Hz per minute between 10Hz and 55Hz, the excursion of the vibration is 1.6mm.The cell shall be vibrated for 30 minutes per axis of XYZ axes.(No leakage No fire )

3.7V 1500mAh Lithium Polymer Battery


Cautions in use:

To ensure proper use of the battery please read the manual carefully before using it. Handling
· Do not expose to, dispose of the battery in fire.
· Do not put the battery in a charger or equipment with wrong terminals connected.
· Avoid shorting the battery
· Avoid excessive physical shock or vibration.
· Do not disassemble or deform the battery.
· Do not immerse in water.
· Do not use the battery mixed with other different make, type, or model batteries.
· Keep out of the reach of children.
Charge and discharge   
· Battery must be charged in appropriate charger only.
· Never use a modified or damaged charger.
· Do not leave battery in charger over 24 hours.
Storage
· Store the battery in a cool, dry and well-ventilated area.
Disposal
· Regulations vary for different countries.  Dispose of in accordance with local regulations


Over-discharging:

It should be noted that the cell would be at over-discharged state by its self-discharge characteristics in case the cell is
not used for long time. In order to prevent over-discharging, the cell shall be charged periodically to maintain between
3.2V and 3.3V.
Over-discharging may causes loss of cell performance, characteristics, or battery functions.
The charger shall be equipped with a device to prevent further discharging exceeding a cut-off voyage specified in the
Product Specification.Also the charger shall be equipped with a device to control the recharging procedures as follows:
The cell battery pack shall start with a low current (0.01C) for 15-30 minutes, i.e.-charging, before rapid charging starts.
The rapid charging shall be started after the (individual) cell voltage has been reached above2.0V within 15-30 minutes
that can be determined with the use of an appropriate timer for pre-charging. In case the (individual) cell voltage does
not rise to 3.0V within the pre-charging time, then the charger shall have functions to stop further charging and display
the cell/pack is at abnormal state.
 
The soft aluminum packing foil is very easily damaged by sharp edge parts such as Ni-tabs, pins and needles.
· Don't strike battery with any sharp edge parts
· Trim your nail or wear glove before taking battery
· Clean worktable to make sure no any sharp particle

   
Any size can be custom-made.

This is for your reference, if any other battery you interested in, please let me know, send us inquiry, we will response as soon as possible. Thank you for your support!


Contact: Doris

Tel: +86 186 6567 6364

Email: info(at)sinolibattery.com

Skype: dorisluo2012

Whatapp: +8618665676364


https://www.google.com/maps/place/%E6%81%92%E8%B6%85%E5%B7%A5%E4%B8%9A%E5%9B%AD/@22.6750062,113.9159113,16z/data=!4m12!1m6!3m5!1s0x340392f0f6365b7d:0xfb2f860e14c76e1a!2z5oGS6LaF5bel5Lia5Zut!8m2!3d22.675111!4d113.919973!3m4!1s0x340392f0f6365b7d:0xfb2f860e14c76e1a!8m2!3d22.675111!4d113.919973